Home Miner Not Hashing? Troubleshooting Guide
Bitaxe or ASIC not hashing? Power, heat, WiFi and stratum fixes, and where each one lives in the SoloFury troubleshooting guide.
Watch on YouTube · 2:59
Chapters
Transcript
The five fixes that solve most cases
If your home miner has gone quiet or stopped hashing, this guide gets you back online. Most dead-miner cases are solved by five simple steps with no tools, starting with a proper cold cycle — unplugging the power connector for sixty seconds, because power faults latch and survive a normal reboot.
This guide is also searchable: every error string is written exactly as the firmware prints it. Just use Ctrl+F to find your specific error, and the guide will take you directly to the fix.
Power, ASIC and thermal problems
The number one cause of miner issues is often found right here in the power section. A miner that appears dead or shows a zero hash rate is frequently suffering from a power fault rather than a failed component.
Next, we look at ASIC problems where the primary concern is the chip’s communication with the board. This area helps diagnose scenarios with zero chips detected or partial counts that indicate sensor bus failures.
Finally, we address thermal problems by treating heat as a budget that needs to be managed. This part of the guide details which numbers actually matter to prevent thermal throttling and ensure stable, long-term operation.
Network and stratum problems
Network problems are often the primary cause for a miner dropping offline, usually stemming from WiFi instabilities like signal interference. One specific trap for home users is the mesh router problem, where automated band steering causes the miner to lose its connection during node handoffs.
As we move further down the guide, we arrive at the stratum and pool problems section, which represents the last mile of communication. This part of the troubleshooting workflow focuses on the specific handshake between your mining hardware and the pool servers.
Within this area, you’ll find solutions for connection refused errors and authorize failures that keep your hash rate from registering properly. Please be wary of the wrong chain address trap, often called the silent killer, as it allows the miner to hash while shares are actually sent to the wrong blockchain.
Symptom table and monthly maintenance
The master symptom table is your first stop for troubleshooting, pairing each symptom with its most likely cause and the immediate first action to take. It’s designed to be the fastest way to self-diagnose your hardware before you even need to touch the machine.
Moving into preventive maintenance, most hardware failures are actually avoidable with this simple fifteen-minute monthly ritual. A short, consistent routine keeps your home miner healthy and helps identify potential issues before they become critical. Whatever your miner is doing, the full step-by-step guide is available at solofury.com, and all links are in the description.
FAQ
Why is my home miner not hashing?
In most cases it is power, heat, network or a stratum misconfiguration rather than a broken chip. A miner that looks dead or sits at zero hashrate is very often a power delivery problem. The fastest first step is a proper cold cycle: unplug the power connector for a full sixty seconds, because power faults can latch and survive a normal reboot.
What is a cold cycle and why does it fix miners?
A cold cycle means fully removing power — unplugging the connector, not just rebooting — for about sixty seconds before powering back on. Voltage regulator faults can latch into a bad state that a normal restart does not clear, but that a full power-down does. It is the single most effective first step for a miner that appears dead.
My miner says it is hashing but the pool shows nothing. Why?
A common cause is pointing the miner at the wrong chain's stratum address — the guide calls this the silent killer. The machine looks like it is working and reports a hashrate locally, but the shares are sent to a different chain's pool and never register where you expect. Checking that the stratum URL matches the coin you intend to mine usually resolves it.
How do I stop my miner from overheating?
Treat heat as a budget, not an event. The guide shows which temperatures actually matter, how to recognise thermal throttling by its pattern in the hashrate, and when the fan itself has become the problem. Improving airflow and ambient temperature is usually more effective than pushing higher clocks.
Why does my miner keep disconnecting from WiFi?
Home setups are often hit by the mesh-router problem: automated band steering hands the miner between nodes and drops the connection during the handoff. Small ASIC and Bitaxe-class devices with basic WiFi are especially sensitive. Locking the miner to a single band or access point usually stabilises it.